HappyModel Moblite7 Walksnail V3 1S 75mm HD Brushless Whoop SuperX HD ELRS AIO EX1002 KV20000 Walksnail Avatar Mini 1S Kit

Specifications: Brand Name: Happymodel Model: Moblite7 Walksnail V3 Frame wheelbase: 75mm Weight: 34.5 gram without battery Size: 98mm*98mm*48mm UART ELRS v3.0 ready Compatible with 1S Lipo battery or Lihv battery Battery Plug: GNB A30 Onboard blackbox ready Package includes: Item Name Qty Mobula7 v4 75mm frame +Canopy 1 SuperX HD ELRS AIO flight controller 1 Happymodel 1002 KV20000 Unibell brushless motor 4 Gemfan 1610-2 bi-blades propeller(4cw+4ccw) 1 Walksnail Avatar nano HD camera 1 Walksnail Avatar mini 1s tx module 1 Spare Canopy 1 Propeller disassemble tool 1 Screw driver 1 Flight controller SuperX HD ELRS Betaflight 4.4.2 firmware ready Firmware target: CRAZYBEEF4DX MCU:STM32F411CEU6 (100MHz, 512K FLASH) Sensor: BMI270 or ICM42688P (SPI connection) Power supply: 1-2S Lipo Lihv battery input (DC 2.8V~8.7V), only support 1s input for this drone Built-in 12A(each) Blheli_S 4in1 ESC Dshot300 read Built-in UART elrs receiver , elrs v3.0 ready, support WIFI and pass-through firmware update Bluejay ESC Firmware ready Built-in 5V 1A BEC Built-in voltage detection No betaflight analog osd chip Onboard 4in1 ESC Power supply: 1-2S LiPo/LiPo HV Current: 12A continuous peak 15A (3 seconds) Support ESC-Configurator and BLHELI_S Suite configurator Factory firmware: Z-H-30 – Bluejay, 0.19, 48kHz Default protocol: DSHOT300 Onboard UART ExpressLRS 2.4GHz Receiver RF Frequency: 2.4GHz Antenna: enameled copper wire 31mm length Telemetry output Power: <12dBm Receiver protocol: CRSF Default firmware version: ExpressLRS V3.0.1 The same hardware with Happymodel EP1 receiver Could update firmware via ExpressLRS configurator or WIFI or Betaflight pass-through Motor Model: 1002 20000KV Configu-ration:9N12P Stator Diameter:10mm Stator Length:2mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.*Len):Φ13.5mm*12.5mm Weight(g):2.5g No.of Cells(Lipo):1S only Propeller Gemfan 1610-2 Bi-blades Weight:0.24g Material: PC Pitch:1 inch Props Dia:40mm Center Hole Dia:1.5mm VTX Model: Avatar mini 1s module Communication Frequency: 5.725-5.850 GHz Transmitter Power(EIRP): FCC:<25.5dBm; CE:<14dBm; SRRC: <20dBm;MIC:<25dBm l/o Interface: JST1.O*6(Power in)JST1.O*4(USB) Mounting Holes: 25.5*25.5 mm Dimensions: 33*33*6.5 mm Storage: 8G Recording: 1080p/720p Weight: 6.8 g Operating Temperature: -20-40℃ Channels: 8 Wide Power lnput: 3.1V-5V Supported FC System: Betaflight OSD: Canvas mode Bitrate: 25mbps / 50mbps Latency: Average delay 22ms Antenna connector: IPEX Camera Model: Avatar nano lmage Sensor: 1/2.7"Inch Resolution: 1080P/6Ofps,720P/120fps,72OP/6Ofps Ratio: 16/9 4/3 Lens: 2.1mm FOV 170° Aperture: F2.0 Shutter: Rolling shutter Min.Illumination: 0.001Lux Weight: 3.5g Dimensions: 14*14*17mm Coaxial Cable: 45mm

Specifications: Brand Name: Happymodel Model: Moblite7 Walksnail V3 Frame wheelbase: 75mm Weight: 34.5 gram without battery Size: 98mm*98mm*48mm UART ELRS v3.0 ready Compatible with 1S Lipo battery or Lihv battery Battery Plug: GNB A30 Onboard blackbox ready

Model: Moblite7 Walksnail V3

UART ELRS v3.0 ready

Battery Plug: GNB A30

Onboard blackbox ready

Package includes:

Item Name

Qty

Mobula7 v4 75mm frame +Canopy

SuperX HD ELRS AIO flight controller

Happymodel 1002 KV20000 Unibell brushless motor

Gemfan 1610-2 bi-blades propeller(4cw+4ccw)

Walksnail Avatar nano HD camera

Walksnail Avatar mini 1s tx module

Spare Canopy

Propeller disassemble tool

Screw driver

Flight controller

SuperX HD ELRS

Betaflight 4.4.2 firmware ready Firmware target: CRAZYBEEF4DX MCU:STM32F411CEU6 (100MHz, 512K FLASH) Sensor: BMI270 or ICM42688P (SPI connection) Power supply: 1-2S Lipo Lihv battery input (DC 2.8V~8.7V), only support 1s input for this drone Built-in 12A(each) Blheli_S 4in1 ESC Dshot300 read Built-in UART elrs receiver , elrs v3.0 ready, support WIFI and pass-through firmware update Bluejay ESC Firmware ready Built-in 5V 1A BEC Built-in voltage detection No betaflight analog osd chip

Onboard 4in1 ESC

Power supply: 1-2S LiPo/LiPo HV Current: 12A continuous peak 15A (3 seconds) Support ESC-Configurator and BLHELI_S Suite configurator Factory firmware: Z-H-30 – Bluejay, 0.19, 48kHz Default protocol: DSHOT300

Onboard UART ExpressLRS 2.4GHz Receiver

RF Frequency: 2.4GHz Antenna: enameled copper wire 31mm length Telemetry output Power: <12dBm Receiver protocol: CRSF Default firmware version: ExpressLRS V3.0.1 The same hardware with Happymodel EP1 receiver Could update firmware via ExpressLRS configurator or WIFI or Betaflight pass-through

Motor

Model: 1002 20000KV Configu-ration:9N12P Stator Diameter:10mm Stator Length:2mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.*Len):Φ13.5mm*12.5mm Weight(g):2.5g No.of Cells(Lipo):1S only

Propeller Gemfan 1610-2 Bi-blades

Weight:0.24g Material: PC Pitch:1 inch Props Dia:40mm Center Hole Dia:1.5mm

VTX

Model: Avatar mini 1s module Communication Frequency: 5.725-5.850 GHz Transmitter Power(EIRP): FCC:<25.5dBm; CE:<14dBm; SRRC: <20dBm;MIC:<25dBm l/o Interface: JST1.O*6(Power in)JST1.O*4(USB) Mounting Holes: 25.5*25.5 mm Dimensions: 33*33*6.5 mm Storage: 8G Recording: 1080p/720p Weight: 6.8 g Operating Temperature: -20-40℃ Channels: 8 Wide Power lnput: 3.1V-5V Supported FC System: Betaflight OSD: Canvas mode Bitrate: 25mbps / 50mbps Latency: Average delay 22ms Antenna connector: IPEX

Camera

Model: Avatar nano lmage Sensor: 1/2.7"Inch Resolution: 1080P/6Ofps,720P/120fps,72OP/6Ofps Ratio: 16/9 4/3 Lens: 2.1mm FOV 170° Aperture: F2.0 Shutter: Rolling shutter Min.Illumination: 0.001Lux Weight: 3.5g Dimensions: 14*14*17mm Coaxial Cable: 45mm